Electrical machinery – Core Synthesis Technology https://www.wixhc.com.cn CNC industry leader Mon, 20 Oct 2025 09:03:48 +0000 en-US hourly 1 https://wordpress.org/?v=6.8.5 LXWGP-ETS-SIEMENS wired electronic handwheel https://www.wixhc.com.cn/product/lxwgp-ets-siemens%e6%9c%89%e7%ba%bf%e7%94%b5%e5%ad%90%e6%89%8b%e8%bd%ae Mon, 20 Oct 2025 08:48:17 +0000 https://www.wixhc.com.cn/?post_type=product&p=25870

电子手轮是用于数控机床手动引导、position、Tool setting and other operations。This model of electronic handwheel is a Siemens wired electronic handwheel with real display.，The handwheel is connected to the X130 interface of the Siemens system through a network cable.，Read the system coordinates and display them to the LCD display of the handwheel through S7 protocol communication.，And the handwheel control system axis selection can be made through communication.、magnification、Button and other signals。

1.采用6芯航空插头线缆连接，手轮线缆长度10米。
2.手轮屏幕可以显示系统工件坐标、机械坐标、进给速度、轴选、倍率等信息。
3.Support emergency stop button，Switching quantity IO signal output，手轮关机急停依然有效。
4.支持6个自定义按钮，开关量IO信号，可以通过IO接线或通信输出信号给系统。
5.支持6或8轴控制，开关量IO信号，可以通过IO接线或通信输出信号给系统。
6.支持3或4档倍率控制，开关量IO信号，可以通过IO接线或通信输出信号给系统。
7.Support pulse encoder，100脉冲/圈，可以通过AB脉冲接线输出信号给系统。
8.Support Siemens S7 protocol，Support Siemens 828D、840DSL、ONE and other model systems。

手轮工作电源电压 DC24V/1A
Receiver supply voltage DC24V/1A
接收器IO输出负载范围
DC24V
手轮端线缆长度
10m
接收器端线缆长度
1m
接收器端网线长度
3m
working temperature
-25℃<X<55℃
Anti-fall height
1m
Number of custom buttons 6个
产品尺寸 233*90.7*77.4（mm）


Comment：
①急停按钮：
Press the emergency stop button，Two sets of emergency stop IO outputs on the receiver are disconnected，And all functions of the handwheel are invalid。
After releasing the emergency stop，The emergency stop IO output on the receiver is closed，All functions of the handwheel restored。

②屏幕显示：

PLC：0000代表网线没有连通，PLC：1010代表网线和PLC系统连接成功，

PLC：1110代表手轮写入系统数据成功，PLC：0001代表连接电脑成功。

③自定义按钮：
6custom buttons，Each button corresponds to an IO output point on the receiver，也通过通信与系统连接。
④轴选开关：
Switching the axis selection switch can switch the moving axis controlled by the handwheel.。
⑤使能按钮：
按住两侧任意一个使能按钮，摇动脉冲编码器才有效。 并且接收器上的2组使能IO输出导通，Release the enable button，Enable IO output disconnection。
⑥倍率开关：
切换倍率开关可以切换手轮控制的倍率。
⑦脉冲编码器：
Press and hold the enable button，Shake pulse encoder，Send a pulse signal，Control machine axis movement。
⑧手轮线缆：

手轮和接收器连接的线缆，航空插头，用于手轮供电和通信。



6.1Product installation steps
1.将接收器通过四个角的螺丝孔将其安装在电柜里。
2.Refer to our receiver wiring diagram，Check against your field equipment，将设备通过线缆和接收器
连接，用网线把接收器和系统的X130接口连接好。
3.After the receiver is fixed，将航空插头底座安装在面板的手轮开孔位置，底座另一
端线排插在接收器上的手轮接口处。然后将手轮端线缆航空插头插入底座，拧紧
固定装置。
6.2Receiver installation dimensions

6.3航空插头安装尺寸

6.4Receiver wiring reference diagram

1.Receiver powered on，The receiver working indicator light flashes，用网线将接收器和电脑连接，设置电脑的固定IP地址，使用网络配置工具软件对手轮功能进行网络参数设置，具体设置
方法参考《LXWGP-ETS有线手轮的使用说明》。
2.接收器设置完成之后，系统需要编程PLC程序，具体请参考《LXWGP-ETS不同西门子数控系统的设置方法》以及PLC程序例程资料。
3.以上设置完成之后，将接收器拿到机器电柜安装好，网线从电脑拔出插到系统的X130接口上，接收器电源和脉冲线插好。
4.Machine powered on，Receiver powered on，The receiver working indicator light flashes，打开手轮电源开关，手轮屏幕开机，屏幕显示PLC:1010，代表手轮和系统通信成功。
5.选中轴选：Toggle axis selection switch，Select the axis you want to operate。
6.Select magnification：Switch magnification switch，Select the magnification file you need。
7.moving axis：Press and hold the enable button，Select the axis selector switch，Select the magnification switch，Then turn the pulse encoder，Turn clockwise to move the axis forward，Counterclockwise rotation of the negative moving axis。
8.Press and hold any custom button，The IO output of the corresponding button of the receiver is turned on，Release button output turns off。
9.Press the emergency stop button，The receiver disconnects the emergency stop IO output，Handwheel function failure，Release the emergency stop button，Emergency stop IO output is closed，Handwheel function restored。



Failure situation Possible reasons
Troubleshooting
Troubleshooting
1.手轮和接收器之间的航空线缆是否正确可靠连接
2.接收器电源电压是否足够
3.Handwheel failure
1.检查手轮和接收器之间的航空线缆的连接情况
2.检查接收器输入电源
3.Contact the manufacturer and return to the factory for maintenance
手轮操作无反应
1.接收器和系统的网线是否连接
2.系统PLC程序是否写好
3.接收器配置是否设置正确
4.手轮显示屏485通信图标是否显示失败
5.操作手轮时，需要按住两侧的使能按钮
6.急停按钮是否释放
1.检查接收器和系统X130网口是否用网线连接
2.检查确认系统PLC是否按照我们提供的参考资料写好
3.检查确认接收器是否参考我们的资料和提供的工具软件，正确的设置了接收器的网络参数和DB地址等
4.检查手轮和接收器之间的
6芯绿色插座，其中的两根通信线：485-A和485-B，是否正确并牢固连接，是否存在断路的情况
After the receiver is powered on，接收器上工作灯不亮
1.Power supply abnormality
2.Power wiring error
3.Receiver failure
1.Check if the power supply has voltage，
Does the voltage meet the requirements?
2.Check whether the positive and negative poles of the power supply are connected reversely
3.Return to factory for repair

1.Please keep it at normal temperature and pressure，Use in dry environment，Extend service life。
2.Please avoid getting exposed to rain、Use in abnormal environments such as blisters，Extend service life。
3.Please keep the appearance of the handwheel clean，Extend service life。
4.Please avoid squeezing、fall、Bump and wait，Prevent damage to the precision parts inside the handwheel or accuracy errors。
5.Not used for a long time，Please store the handwheel in a clean and safe place。
6.Pay attention to moisture-proof and shock-proof when storing and transporting。

1.Please read the instructions carefully before use，Operation by non-professionals is prohibited。
2.手轮出现任何非正常情况后，请立即停止使用，并且排查故障，在故障排除前，禁止再使用故障手轮，避免因手轮未知故障而发生安全事故；
3.Need repair，Please contact the manufacturer，If the damage is caused by self-repair，The manufacturer will not provide warranty。
]]> Special wireless electronic handwheel for CNC mount https://www.wixhc.com.cn/product/%e6%95%b0%e6%8e%a7%e7%ab%8b%e8%bd%a6%e4%b8%93%e7%94%a8%e6%97%a0%e7%ba%bf%e7%94%b5%e5%ad%90%e6%89%8b%e8%bd%ae Thu, 21 Aug 2025 05:41:33 +0000 https://www.wixhc.com.cn/?post_type=product&p=25816

The special wireless electronic handwheel for CNC vertical lathes is used for manual guidance of CNC vertical machine tools.、position、Tool setting and other operations。This product uses wireless transmission technology，Eliminates traditional spring wire connections，Reduce equipment failures caused by cables，Eliminate cable dragging，Disadvantages such as sticking to oil stains，More convenient to operate。Widely applicable to CNC vertical lathes、Single column vertical lathe、Double column vertical lathe and other vertical lathes。And can be adapted to various CNC systems on the market，Such as Siemens、mitsubishi、Fanuc、Xindai and other CNC system brands。

1.Using 433MHZ wireless communication technology，Wireless operating distance 40 meters。
2.Adopt automatic frequency hopping function，Use 32 sets of wireless remote controls at the same time，No effect on each other。
3.Support emergency stop button，Switching quantity IO signal output。
4.Supports 2 custom buttons，Switching quantity IO signal output。
5.Support 2-axis control。
6.Supports 3 levels of magnification control。
7.Support enable button function，Can output switching IO signals，You can also control axis selection、magnification and encoder。
8.Support axis selection and magnification to modify the encoding type through software。
9.Support pulse encoder，Specification: 100 pulses/turn。

Handheld terminal operating voltage and current 3 V/14 mA
Battery specifications 2AA alkaline batteries
Handheld terminal low voltage alarm range
<2.3V
Receiver supply voltage DC5V-24V/1A
Receiver emergency stop output load range AC125V-1A/DC30V-2A
Receiver enable output load range AC125V-1A/DC30V-2A
Receiver custom button output load range DC24V/50mA
Receiver axis selection output load range DC24V/50mA
Receiver multiplier output load range DC24V/50mA
Handheld terminal transmit power
15dBm
Receiver receiving sensitivity -100dBm
Wireless communication frequency
433MHz frequency band
Wireless communication distance
Accessible distance 40 meters
working temperature -25℃<X<55℃
Anti-fall height Comply with national testing standards
Number of custom buttons (2 pieces)

Right column hand wheel(Right tool holder hand wheel)
model：ZTWGP03-2AA-2-05-R

Left column hand wheel(Left tool rest handwheel)
model：ZTWGP03-2AA-2-05-L
Right column hand wheel(Right tool holder hand wheel)
model：STWGP03-2AA-2-05-R

Left column hand wheel(Left tool rest handwheel)
model：STWGP03-2AA-2-05-L

Comment：

①Pulse encoder：
Press and hold the enable button，Shake pulse encoder，Send a pulse signal，Control machine axis movement。
②Enable button：
Press either enable button on both sides，Two sets of enable IO outputs on the receiver are turned on，Release the enable button，Enable IO output disconnection；And when switching the axis selection magnification，and before turning the hand wheel，Need to press and hold the enable button to be effective；This function can be canceled through the configuration software。
③Indicator light：
left light：Power on light，Use the handwheel to select the axis OFF to start the machine.，This light is always on after turning on the machine；
middle light：signal light，When operating any function of the handwheel，This light is on，Does not light up when there is no operation；
Right light：Low voltage warning light，Battery power is too low，This light flashes or stays on，Need to replace battery。
④Emergency stop button：
Press the emergency stop button，Two sets of emergency stop IO outputs on the receiver are disconnected，And all functions of the handwheel are invalid。

Release emergency stop，The emergency stop IO output on the receiver is closed，All functions of the handwheel restored。

⑤Magnification switch：
Press and hold the enable button，Switch magnification switch，The magnification controlled by the handwheel can be switched。
⑥Axis selection switch (power switch)：
Press and hold the enable button，Switching the axis selection switch can switch the moving axis controlled by the handwheel.。Switch this switch from OFF to any axis，Handwheel power on。
⑦Custom button：
2custom buttons，Each button corresponds to an IO output point on the receiver。
Product installation steps
1.Install the receiver into the electrical cabinet through the buckle on the back，Or install it in the electrical cabinet through the screw holes at the four corners of the receiver。
2.Refer to our receiver wiring diagram，Check against your field equipment，Connect the device to the receiver via cable。
3.After the receiver is fixed，The antenna equipped with the receiver must be connected，And install or place the outer end of the antenna outside the electrical cabinet，It is recommended to place it on the top of the electrical cabinet for the best signal effect.，It is prohibited to leave the antenna unconnected，Or place the antenna inside the electrical cabinet，May cause the signal to become unusable。
4.Finally turn on the handwheel power switch，You can operate the hand wheel remote control machine。
Receiver installation dimensions

Receiver wiring reference diagram

1.Machine powered on，Receiver powered on，The receiver working indicator light flashes，Install the battery on the wireless electronic handwheel，Fasten the battery cover，Turn on the wireless electronic handwheel power switch，The hand wheel battery light is on。
2.Select axis：Press and hold the enable button，Toggle axis selection switch，Select the axis you want to operate。
3.Select magnification：Press and hold the enable button，Switch magnification switch，Select the magnification file you need。
4.moving axis：Press and hold the enable button，Select the axis selector switch，Select the magnification switch，Then turn the pulse encoder，Turn clockwise to move the axis forward，Counterclockwise rotation of the negative moving axis。
5.Press and hold any custom button，The IO output of the corresponding button of the receiver is turned on，Release button output turns off。
6.Press the emergency stop button，The receiver disconnects the emergency stop IO output，Handwheel function failure，Release the emergency stop button，Emergency stop IO output is closed，Handwheel function restored。
7.Do not operate the handwheel for a period of time，The handwheel automatically enters sleep standby，Reduce power consumption，when using again，The handwheel can be activated by pressing the enable button。

8.Do not use the handwheel for a long time，It is recommended to switch the handwheel shaft to the OFF position，Turn off handwheel power，Extend battery life。

①：ZTWGP represents appearance style

②：Pulse output parameters：
01：Indicates that the pulse output signal is A、B；Pulse voltage 5V；Number of pulses 100PPR。
02：Indicates that the pulse output signal is A、B；Pulse voltage 12V；Number of pulses 25PPR。
03：Indicates that the pulse output signal is A、B、A-、B-；Pulse voltage 5V；Number of pulses 100PPR。
04：Indicates low level NPN open circuit output，The pulse output signal is A、B；Number of pulses 100PPR。
05：Indicates high level PNP source output，The pulse output signal is A、B；Number of pulses 100PPR。
③：Represents the number of axis selector switches，2Represents 2 axes。
④：Represents the axis selection switch signal type，A represents point-to-point output signal，B represents the encoded output signal。
⑤：Represents the magnification switch signal type，A represents point-to-point output signal，B represents the encoded output signal。
⑥：Represents the number of custom buttons，2Represents 2 custom buttons。
⑦：Represents the system handwheel power supply，05Represents 5V power supply。
⑧：L stands for left column (left tool rest)，R stands for right column (right tool rest)。

Failure situation Possible reasons
Troubleshooting
Turn OFF switch，
Unable to boot，
The power light does not light up
1.Handwheel without battery installed
Or the battery is installed abnormally
2.Battery is low
3.Handwheel failure
1.Check the installation of handwheel battery
2.Replacement battery
3.Contact the manufacturer and return to the factory for maintenance
Handwheel startup，
No response from operation，
During operation，Handwheel signal
The light is off
1.Receiver is not powered on
2.The receiver antenna is not installed
3.The distance between the remote control and the machine is too far
4.environmental interference
5.Enable is not pressed during handwheel operation
button
1.Check that the receiver is powered on
2.Install the receiver antenna，And install the outer end of the antenna outside the electrical cabinet and fix it
3.Operate at normal distance
4.①Optimize electrical cabinet wiring，Keep the receiver antenna wiring as far away as possible from 220V and above
Try to use an independent switching power supply for the upper line ② receiver power supply.，and
Add power isolation module and magnetic ring to the power cord，Increase anti-interference ability
Handwheel startup，
Low voltage warning light flashes
1.Battery is low
2.Abnormal battery installation or poor contact
1.Replacement battery
2.Check battery installation，And whether the metal sheets at both ends of the battery compartment are dry
No foreign matter，clean it
Hand wheel press button，
or turn the switch，
or shake pulse encoder，
No response
1.Switch/Button/Pulse Encoder
Damage fault
2.Receiver damage failure
1.Observe turning a switch or pressing a button
Or when shaking the pulse encoder，Is the signal light of the handwheel flashing?，Not bright
Meter switch or button or encoder failure，Return to factory for repair；Light means normal，check
Check whether the receiver wiring is correct
2.Return to factory for repair
After the receiver is powered on，
No lights on the receiver
1.Power supply abnormality
2.Power wiring error
3.Receiver failure
1.Check if the power supply has voltage，Does the voltage meet the requirements?
2.Check whether the positive and negative poles of the power supply are connected reversely
3.Return to factory for repair

1.Please keep it at normal temperature and pressure，Use in dry environment，Extend service life。
2.Please avoid getting exposed to rain、Use in abnormal environments such as blisters，Extend service life。
3.Please keep the appearance of the handwheel clean，Extend service life。
4.Please avoid squeezing、fall、Bump and wait，Prevent damage to the precision parts inside the handwheel or accuracy errors。
5.Not used for a long time，Please store the handwheel in a clean and safe place。
6.Pay attention to moisture-proof and shock-proof when storing and transporting。
1.Please read the instructions carefully before use，Operation by non-professionals is prohibited。
2.Please replace the battery in time when the battery is too low，Avoid errors caused by insufficient power causing the handwheel to be inoperable。
3.Need repair，Please contact the manufacturer，If the damage is caused by self-repair，The manufacturer will not provide warranty。
]]> Fanako system dedicated handwheel XWGP–Ets-Fanuc https://www.wixhc.com.cn/product/%e5%8f%91%e9%82%a3%e7%a7%91%e7%b3%bb%e7%bb%9f%e4%b8%93%e7%94%a8%e6%89%8b%e8%bd%aexwgp-ets-fanuc Tue, 06 May 2025 07:03:25 +0000 https://www.wixhc.com.cn/?post_type=product&p=25797

无线电子手轮是用于数控机床手动引导、position、Tool setting and other operations。This product uses wireless transmission technology，Eliminates traditional spring wire connections，Reduce equipment failures caused by cables，Eliminate cable dragging，Disadvantages such as sticking to oil stains，More convenient to operate。该型号无线电子手轮是发那科系统专用手轮，通过IO-LINK协议实现发那科系统坐标实时在手轮屏幕显示，并且通过IO-LINK协议，直接把轴选、magnification、按钮信号接入系统，减少接线。

1.Using 433MHZ wireless communication technology，Wireless operating distance 40 meters；
2.Adopt automatic frequency hopping function，Use 32 sets of wireless remote controls at the same time，No effect on each other；
3.Support emergency stop button，Switching quantity IO signal output，通过IO接线和系统连接；
4.支持4个自定义按钮，开关量IO信号，通过IO-LINK协议输出信号给系统；
5.支持快捷移动按钮+和按钮-，按住按钮可以代替摇手轮移动机器；
6.支持6轴控制，开关量IO信号，通过IO-LINK协议输出信号给系统；
7.Supports 3 levels of magnification control，开关量IO信号，通过IO-LINK协议输出信号给系统；
8.Support enable button function，通过IO接线和系统连接，同时控制编码器使能；
9.Support pulse encoder，100脉冲/圈，通过输出AB编码信号接入系统MPG 手轮接口；


Comment：
Comment：
①急停按钮：
Press the emergency stop button，Two sets of emergency stop IO outputs on the receiver are disconnected，And all functions of the handwheel are invalid。After releasing the emergency stop，The emergency stop IO output on the receiver is closed，All functions of the handwheel restored。
②屏幕显示：
③自定义按钮：
4custom buttons，Each button corresponds to an IO output point on the receiver，通过IO-LINK与系统连接。一般把~按钮设置为高速按钮。
④轴选开关：
Switching the axis selection switch can switch the moving axis controlled by the handwheel.。
⑤快捷按钮：
按下快捷按钮+，机器正向移动，按下快捷按钮-，机器负向移动，可以代替摇手轮移动机器。
⑥使能按钮：

按住两侧任意一个使能按钮，摇动脉冲编码器才有效。 并且接收器上的2组使能IO输出导通，Release the enable button，Enable IO output disconnection。

⑦倍率开关：

切换倍率开关可以切换手轮控制的倍率。

⑧脉冲编码器：

Press and hold the enable button，Shake pulse encoder，Send a pulse signal，Control machine axis movement。

⑨电源开关：
手轮开机按钮。



Product installation steps：
1.Install the receiver into the electrical cabinet through the buckle on the back，Or install it in the electrical cabinet through the screw holes at the four corners of the receiver。
2.Refer to our receiver wiring diagram，Check against your field equipment，Connect the device to the receiver via cable。
3.After the receiver is fixed，The antenna equipped with the receiver must be connected，And install or place the outer end of the antenna outside the electrical cabinet，It is recommended to place it on the top of the electrical cabinet for the best signal effect.，It is prohibited to leave the antenna unconnected，Or place the antenna inside the electrical cabinet，May cause the signal to become unusable。

4.Finally turn on the handwheel power switch，You can operate the hand wheel remote control machine。

Receiver installation dimensions：

Receiver wiring reference diagram：

1.Please keep it at normal temperature and pressure，Use in dry environment，Extend service life；
2.Please avoid getting exposed to rain、Use in abnormal environments such as blisters，Extend service life；
3.Please keep the appearance of the handwheel clean，Extend service life；
4.Please avoid squeezing、fall、Bump and wait，Prevent damage to the precision parts inside the handwheel or accuracy errors；
5.Not used for a long time，Please store the handwheel in a clean and safe place；
6.Pay attention to moisture-proof and shock-proof when storing and transporting。
1.Please read the instructions carefully before use，Operation by non-professionals is prohibited；
2.电量过低时请及时充电，Avoid errors caused by insufficient power causing the handwheel to be inoperable；
3.Need repair，Please contact the manufacturer，If the damage is caused by self-repair，The manufacturer will not provide warranty。
]]> Industrial wireless remote control DH01R-4W-26K https://www.wixhc.com.cn/product/dh01r-4w-26k Fri, 05 Jan 2024 03:05:37 +0000 https://www.wixhc.com.cn/?post_type=product&p=25629

model：DH01R-4W-26K adapter equipment：Various industrial equipment

Remark：You can choose one of three antennas，Default standard suction cup antenna

Remark：
① DH01R series，If the suffix contains T, it means with emergency stop output.；Without T means without emergency stop output。
②If there is no analog output，No need to remark 0W or 0R；Analog quantities W1, W2, W3, and W4 default to 0-10V analog voltage output；At the same time, W1 and W2 can expand 2 isolated digital potentiometer outputs.，Range 0-5K ohms，1/2watt；resolution：20ohm。The two digital potentials can be used to control the welding current and welding voltage of the welding machine.。If the digital potentiometer output is required，User notes required。
④Analog input，范围从1到2，Indicates that there are 1 to 2 analog inputs (maximum 2 channels)；When there is an analog input，Need to note the voltage range of the analog input (our receiver defaults to 0-5V，Users can also note 4-20 mA or 0-10V, etc.) and the corresponding display range of the analog quantity.(for example：Displays 0-100 volts or 0-1000 amps)
These two analog quantities can be used as displays for welding current and welding voltage.。

W1 knob value：W1：0-1000(Parameter adjustable 0-9999)
W2 knob value：W2：0-5000(Parameter adjustable 0-9999)
W3 knob value：W3：0-5000(Parameter adjustable 0-9999)
W4 knob value：W4：0-5000(Parameter adjustable 0-9999)
ADC1 feedback display：0-1000(Parameter adjustable 0-5000)
ADC2 feedback display：0-1000(Parameter adjustable 0-5000)

low pressure：Remote control battery is too low，Please replace the battery

Dropped network：Wireless signal interruption，Please check receiver power supply，Power cycle，Remote control restarts

1、Remote control power on
Receiver powered on，Receiver working indicator flashes；Install two AA batteries in the remote control，Turn on the power switch，The display shows the value，Indicates successful boot。The receiver working indicator light turns to a steady state。

2、Switch and button functions
Operate any of the twist switches and buttons on the remote control，Can control the corresponding switch signal output point at the receiver end，All switch signal output points on the receiver are normally open signals by default.

3、W1-W4 speed adjustment
Rotate the knobs in W1-W4 at will，Can operate the corresponding analog output signal or potentiometer signal at the receiver end，
The analog output signal at the receiver is a 0-10V voltage signal by default，电位器信号默认0-5K；

4、Emergency stop function
Photograph the emergency stop button，All switching signal outputs are disconnected，Analog output disconnected；After releasing the emergency stop，All switching signals restored，Analog output recovery；
5 seconds after the remote control is turned off，All switching signal outputs are disconnected，The analog quantity remains unchanged，Remote control power on，Switch signal output automatically recovers；

5、Parameter menu (users are prohibited from modifying it without permission)
Some functions of the remote control can be adjusted through parameters，When the display screen W1=0，Press the K9-B button 3 times in a row，Then press the K9-A button 3 times in succession，Enter parameter menu；
K9-A and K9-B keys are used to turn menu pages and select parameters.；Hold K1-A，Press the K9-A/B button again，Modify parameters；
Exit parameter menu：Choose to save or not save，Then press the K1-A button to confirm the exit；
F1W1 range:The display range value of the W1 knob on the display screen，0-9999Adjustable；
F2W2 scope:The display range value of the W2 knob on the display screen，0-9999Adjustable；
F3W3 scope:The display range value of the W3 knob on the display screen，0-9999Adjustable；
F4W4 scope:The display range value of the W4 knob on the display screen，0-9999Adjustable；
F5A1 range:Display ADC1 feedback display range value，0-5000Adjustable；
F6A2 range:Display ADC2 feedback display range value，0-5000Adjustable；
告警电流：Set the alarm value for ADC1 and ADC2 feedback display，When ADC1 and 2 exceed this value，Remote control display alarm prompt；When this value is 0，Alarm function is invalid；

 

The final right of interpretation of this product belongs to Chengdu Core Synthetic Technology Co., Ltd.。

]]> Roller frame, wire saw cutting, multi-functional industrial remote control, DH01R https://www.wixhc.com.cn/product/%e6%bb%9a%e8%bd%ae%e6%9e%b6-%e7%bb%b3%e9%94%af%e5%88%87%e5%89%b2-%e5%a4%9a%e5%8a%9f%e8%83%bd%e5%b7%a5%e4%b8%9a%e9%81%a5%e6%8e%a7%e5%99%a8-dh01r Wed, 22 Jul 2020 03:47:37 +0000 https://www.wixhc.com.cn/?post_type=product&p=10296

]]> 6Custom buttons New generation system Wireless electronic handwheel XWGP https://www.wixhc.com.cn/product/6%e4%b8%aa%e8%87%aa%e5%ae%9a%e4%b9%89%e6%8c%89%e9%94%ae-%e6%96%b0%e4%bb%a3%e7%b3%bb%e7%bb%9f-%e6%97%a0%e7%ba%bf%e7%94%b5%e5%ad%90%e6%89%8b%e8%bd%ae-xwgp Fri, 17 Jul 2020 05:12:40 +0000 https://www.wixhc.com.cn/?post_type=product&p=9932  

Features

1、Wireless ISM band，433MHZ。

2、With emergency stop button function,and 6 extended key outputs。

3、Anti-interference design，Stable and reliable，Use 32 sets of wireless handwheels in the same room，No effect on each other。

4、Low power consumption design，2AA batteries，30 days of normal use。

5、With axis selection function，Magnification selection function。

6、Adopt alloy encoder，Stable and reliable performance，Good feel，Clear tooth position。

 

 

]]> Roller frame, wire saw cutting, multi-functional industrial remote control, DH12S-2R-4K https://www.wixhc.com.cn/product/%e6%bb%9a%e8%bd%ae%e6%9e%b6-%e7%bb%b3%e9%94%af%e5%88%87%e5%89%b2-%e5%a4%9a%e5%8a%9f%e8%83%bd%e5%b7%a5%e4%b8%9a%e9%81%a5%e6%8e%a7%e5%99%a8-dh12s-2r-4k Fri, 17 Jul 2020 05:12:28 +0000 https://www.wixhc.com.cn/?post_type=product&p=9931

电气规格参数

无线遥控器电气参数
工作电压 2节5AA电池，2v-3.0V
工作电流 平均电流小于4mA

 

 

无线接收器电气参数
接收器输入电源 5-24V(5W)
输出口负载能力 AC250V/3A或DC30V/5A
数字电位器输出口 满量程5.1K欧姆
模拟量电压输出口 0-10V输出

 

 

]]> Simple version New generation system Wireless electronic handwheel EWGP https://www.wixhc.com.cn/product/ewgp Wed, 08 Jan 2020 08:49:07 +0000 https://www.wixhc.com.cn/?post_type=product&p=4810

]]> New generation system wireless electronic handwheel BWGP (Aluminum wheels) https://www.wixhc.com.cn/product/wireless-handwheel-bwgp-2 Wed, 27 Nov 2019 03:51:57 +0000 https://www.wixhc.com.cn/?post_type=product&p=3656

]]> CNC lathe wireless electronic handwheel SWGP https://www.wixhc.com.cn/product/wireless-mpg-swgp Wed, 27 Nov 2019 03:51:55 +0000 https://www.wixhc.com.cn/?post_type=product&p=3655

]]>