Fanako system dedicated handwheel XWGP–Ets-Fanuc

无线电子手轮是用于数控机床手动引导、position、Tool setting and other operations。This product uses wireless transmission technology，Eliminates traditional spring wire connections，Reduce equipment failures caused by cables，Eliminate cable dragging，Disadvantages such as sticking to oil stains，More convenient to operate。该型号无线电子手轮是发那科系统专用手轮，通过IO-LINK协议实现发那科系统坐标实时在手轮屏幕显示，并且通过IO-LINK协议，直接把轴选、magnification、按钮信号接入系统，减少接线。

1.Using 433MHZ wireless communication technology，Wireless operating distance 40 meters；

2.Adopt automatic frequency hopping function，Use 32 sets of wireless remote controls at the same time，No effect on each other；

3.Support emergency stop button，Switching quantity IO signal output，通过IO接线和系统连接；

4.支持4个自定义按钮，开关量IO信号，通过IO-LINK协议输出信号给系统；

5.支持快捷移动按钮+和按钮-，按住按钮可以代替摇手轮移动机器；

6.支持6轴控制，开关量IO信号，通过IO-LINK协议输出信号给系统；

7.Supports 3 levels of magnification control，开关量IO信号，通过IO-LINK协议输出信号给系统；

8.Support enable button function，通过IO接线和系统连接，同时控制编码器使能；

9.Support pulse encoder，100脉冲/圈，通过输出AB编码信号接入系统MPG 手轮接口；

Comment：

②屏幕显示：

③自定义按钮：

4custom buttons，Each button corresponds to an IO output point on the receiver，通过IO-LINK与系统连接。一般把~按钮设置为高速按钮。

④轴选开关：

Switching the axis selection switch can switch the moving axis controlled by the handwheel.。

⑤快捷按钮：

按下快捷按钮+，机器正向移动，按下快捷按钮-，机器负向移动，可以代替摇手轮移动机器。

⑥使能按钮：

按住两侧任意一个使能按钮，摇动脉冲编码器才有效。 并且接收器上的2组使能IO输出导通，Release the enable button，Enable IO output disconnection。

⑦倍率开关：

切换倍率开关可以切换手轮控制的倍率。

⑧脉冲编码器：

Press and hold the enable button，Shake pulse encoder，Send a pulse signal，Control machine axis movement。

⑨电源开关：

手轮开机按钮。

Product installation steps：
1.Install the receiver into the electrical cabinet through the buckle on the back，Or install it in the electrical cabinet through the screw holes at the four corners of the receiver。

2.Refer to our receiver wiring diagram，Check against your field equipment，Connect the device to the receiver via cable。

3.After the receiver is fixed，The antenna equipped with the receiver must be connected，And install or place the outer end of the antenna outside the electrical cabinet，It is recommended to place it on the top of the electrical cabinet for the best signal effect.，It is prohibited to leave the antenna unconnected，Or place the antenna inside the electrical cabinet，May cause the signal to become unusable。

4.Finally turn on the handwheel power switch，You can operate the hand wheel remote control machine。

1.Please keep it at normal temperature and pressure，Use in dry environment，Extend service life；

2.Please avoid getting exposed to rain、Use in abnormal environments such as blisters，Extend service life；

3.Please keep the appearance of the handwheel clean，Extend service life；

4.Please avoid squeezing、fall、Bump and wait，Prevent damage to the precision parts inside the handwheel or accuracy errors；

5.Not used for a long time，Please store the handwheel in a clean and safe place；

6.Pay attention to moisture-proof and shock-proof when storing and transporting。

1.Please read the instructions carefully before use，Operation by non-professionals is prohibited；

2.电量过低时请及时充电，Avoid errors caused by insufficient power causing the handwheel to be inoperable；

3.Need repair，Please contact the manufacturer，If the damage is caused by self-repair，The manufacturer will not provide warranty。