I-Floor Grinder Wireless Remote Control DH22ST-Le

Ukufanisa

isifanekiso：DH22ST-Le

Izinsiza eziguqukayo：地坪研磨机

Phawula：Ungakhetha eyodwa yezi-antenna ezintathu，I-Antenna evamile yokuthola indawo evamile ye-antenna

急停：急停按钮被拍下，请释放急停按钮

ingcindezi ephansi：Ibhethri lokulawula kude liphansi kakhulu，Sicela ungene esikhundleni sebhethri

Kuhlelwe inethiwekhi：Ukuphazamiseka kwesignali engenantambo，Sicela ubheke ukunikezwa kwamandla okuthola，Umjikelezo wamandla，Ukulawula Ukulawula Okukude

1、Amandla okulawula kude

Somukeli unikwe amandla，Ukukhanya kwe-RF-LED ekwamukeleni kuqala kukhanya；Faka amabhethri amabili e-AA ekulweni okukude，Vula ukushintshwa kwamandla，Ukuboniswa kukhombisa isivinini sezimoto，Kukhombisa i-boot ephumelelayo。

2、照明

按一下“照明”按钮，接收器照明输出打开，显示屏出现照明图标;

再次按一下“照明”按钮，接收器照明输出关闭，显示屏照片图标消失。

3、研磨电机和调速

Vula inkinobho ethi "Phambili / Reverse" phambili，接收器研磨正转打开，Isibonisi sibonisa ukujikeleza phambili

;
Vula inkinobho ethi "Phambili / Reverse" ukuze uguqulwe，接收器研磨反转打开，Khombisa imibukiso ebuyiselwe emuva

;

旋转“研磨调速”旋钮，可以调节接收器研磨调速输出电压大小0-10V；

4、行走电机和调速

Hambisa inkinobho ethi "phambili / emuva" ukuze iqhubekele phambili，Isamukeli esisele isondo phambili kanye nesondo lesokudla phambili livulekile，Isibonisi sibonisa phambili

;

Hambisa "phambili / emuva emuva" switch ukuze ubuye emuva，I-Receiver ishiye isondo emuva nangesondo kwesokudla emuva，Isibonisi sibonisa emuva ;

旋转“行走调速”旋钮，可以调节接收器左轮和右轮调速输出电压大小0-10V；

5、Jikela kwesokunxele nakwesokudla

Vula inkinobho ethi "Kwesobunxele / kwesokudla" uye kwesobunxele，I-Receiver Ngakwesokunene Lika-Wheel Phansi Iyavulwa，Isibonisi sibonisa i-LEFT yesokunxele ;

Vula inkinobho ethi "Jikela kwesobunxele / kwesokudla" ukuze ujike kwesokudla，Isamukeli esisele isondo phambili ukuze livulekile，Isibonisi sibonisa jikela kwesokudla

;

6、Vula indawo

Jika ngakwesokunxele：Cindezela ubambe inkinobho ethi "Vuleko"，将“左转/右转”开关扳到左转位置，接收器左轮后退和右轮前进打开，Qala ukujika kwesokunxele；

Jikela ngakwesokudla：Cindezela ubambe inkinobho ethi "Vuleko"，将“左转/右转”开关扳到右转位置，接收器左轮前进和右轮后退打开，Qala ukujika kwesokudla；

7、急停

拍下急停按钮，接收器急停输出断开；所有开关控制断开，所有速度清零；

8、Ukulungiswa komugqa oqondile

Lapho ama-motor ahamba kwesobunxele nakwesokudla aqhubekela phambili futhi abuyele emuva，Ukungahambisani ngakwesobunxele nakwesobunxele kwesokudla kwenzeka，Ukuphambuka ekuhambeni umugqa oqondile，Ungasebenzisa umsebenzi wokulungiswa oqondile wokulawula okukude，I-Fine-Tune Sune esele nejubane lensimbi yesokudla；

Isimiso sokulungiswa：Ngomsebenzi wokulungiswa，I-Fine-Tune Lishiya Ijubane Lesondo，ukufeza ijubane elifanayo njengesondo elifanele，Zuza ukuvumelanisa kwejubane kwesokunxele nangakwesokudla，Susa i-Offset；

Indlela yokusebenza yokulungisa：Cindezela ubambe inkinobho ethi "Vuleko"，缓慢旋转“直线纠偏”旋钮；

Jikelezisa ngokwewashi，Khulisa Voltage Speed Voltage，Ukubonisa Inani Lokulungiswa Liyanda；

I-CounterclockWise，Yehlisa i-Left Speed Voltage，Inani lokulungiswa kokubonisa liyancipha；

Uhla lokulungiswa：Inani Lokulungiswa -90 kuya ku-90；1个纠偏单位的纠偏电压大约0.04V；

9、Imenyu yepharamitha (abasebenzisi anqatshelwe ekushintsheni ngaphandle kwemvume)

进入参数菜单方式：研磨为0时，正转/反转连续上掰3次，再下掰3次；

退出方式：选择保存或者不保存，按使能按钮确认；

直线微调范围：0-120；

研磨速度：0-3000；

行走速度：0-1000；

Amandla okusebenza	I-DC24V / 1A (Ukunikezwa kwamandla okuzimele)
Umthwalo Omtholwayo Wokukhipha	AC0-250V/3A DC0-30V/5A
I-Voltage esheshayo yokulawula ijubane	I-DC0-10V